Make sure Xdebug or Zend Debugger are configured to connect to the host and port PhpStorm is running on. When the debugger cannot connect or refuses the connection, check the following: ![]() If any errors or warnings are present on the first lines, it's recommended to fix them before continuing. The PHP Group Zend Engine v3.1.0, Copyright (c) 1998-2018 Zend Technologies with Zend OPcache v7.1.20,Ĭopyright (c) 1999-2018, by Zend Technologies with Xdebug v2.6.0, Copyright (c) 2002-2018, by Derick Rethans To verify that no startup warnings or errors are displayed, run the following command: PhpStorm will also not be able to recognize the debugger being used. ![]() When this is the case, the debugger may fail to work. When running PHP, it can happen that a startup warning or error is displayed. To validate the debugging engine configuration, perform the steps described in Validate the configuration of a debugging engine Startup warnings and errors preventing the debugger from working To avoid this problem, you need to update the corresponding sections in the php.ini file as described in Configure Xdebug and Configure Zend Debugger. These tools cannot be used simultaneously because they block each other. To debug PHP code with PhpStorm, make sure that you have a debugging engine, either Xdebug or Zend Debugger, installed and configured properly. Making sure Xdebug or Zend Debugger are installed and configured When logging is no longer needed, it is recommended that you disable it. The log file will not automatically roll over or be truncated and may grow to a vast file size. ![]() To verify that the xdebug process is active xdebug.Log opened at 08:14:28 I: Connecting to configured address/port: 127.0.0.1:9000. (deployed into in the apps etc folder) are different in that way, and are each used depending upon context of the request. May not show that xdebug is enabled as php can be configured to use different settingsįor commandline than it does for web requests. Note: Running basic diagnostics like commandline php -i on the server In Drupal this can be found underneath reports. You may be able to check out a phpinfo diagnostic from within your web application and confirm xdebug is running. To verify that xdebug is being loaded by PHP Looking like xdebug.remote_host = unix:///run/platform/xxxxxxxxxxxxx_stg/xdebug.sock PHP script execution begins, and this starts sending stack trace messages to a socket on that server ( /run/platform/$/,.This is to avoid the performance cost of running xdebug resident or on-demand inside a production PHP service. It reaches the (nginx) webserver, which also recognises the XDEBUG_SESSION_START key, and so passes it to a dedicated xdebug-enabled php service for processing.The request next passes to the load-balancing router, which forwards it to one of three web heads. ![]() This request is routed to the outer (cache) layer of the hosting platform, where the presence of the XDEBUG_SESSION_START key should tell the system not to cache it.You initiate an xdebug session from your browser, by requesting.Once all the server configurations are in place, and your IDE and the tunnels are set up to listen, what happens is this: You normally don’t have to worry about some of these layers, but if any one of them goes wrong, nothing will work, so this may help to narrow in on what does and doesn’t work, when you are setting up for the first time. XDebug extensions installed and activated on your environmentsīefore getting started, it’s helpful to understand what happens at every step in an xdebugging process.An IDE such as PHPStorm with integrated XDebug support.The platform CLI utility installed and configured to connect to the hosting API.A local copy of your project site, with all code files available.It’s not a HOWTO use your IDE, it’s about how to diagnose network or service issues that are specific to the Platform hosting environment. This document is mostly about the nuts-and-bolts of establishing communications between your local development environment and the remote servers. Use your local development environment to do breakpoint debugging on your remote server(s)
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |